How to Tune the Toyan V8 FS-V800BGC Carburetor: Idle Gap, Low & High Speed Needle Settings from Expert Jamie RCBlock | Stirlingkit
November 04, 2026Idle gap
1.1 mm
Set this first
Low speed needle
1.5 turns
Never below 1 turn
High speed needle
2–3 turns
Manual 2.0 · Jamie 3
Fuel mix
25–30 : 1
Gasoline : 2T oil
A Toyan V8 that won't idle, bogs when you open the throttle, or dies when you snap it shut almost always comes down to three settings on the carburetor. This guide explains what each one does, gives you a proven starting point, and shows you how to fine-tune from there.
On Jamie's own FS-V800BGC, the factory carburetor setting needed retuning, so he started from zero and dialed it in step by step. These are the settings he ended up with.
- Idle gap: how far the throttle stays open when the throttle is closed. It sets how much air the engine gets at idle.
- Low speed needle (LSN): called the "auxiliary oil needle" in the Toyan manual. It controls the fuel mixture at idle and low RPM.
- High speed needle (HSN): called the "main oil needle" in the Toyan manual. It controls the fuel mixture at mid to full throttle.
- "Turns out": how many turns the needle is opened, counted from gently seated (fully closed). More turns = more fuel (richer).
- Rich / lean: too much fuel / too little fuel for the amount of air.
Quick Settings: Toyan Manual vs Jamie
| Setting | Toyan manual | Jamie RCBlock |
|---|---|---|
| Idle gap | Less than 1.5 mm | 1.1 mm — set this first |
| Low speed needle | 1.5 turns (minimum 1 turn) | 1.5 turns out |
| High speed needle | 2.0 turns | Flush with the carburetor body, approx. 3 turns out |
Every engine is slightly different. Use these as a starting point, then fine-tune by sound and response as shown below.
Before You Start
- Fuel: quality gasoline mixed with 2T engine oil at 1:25 to 1:30.
- Fuel tank: about 100 cc, mounted level with the engine. Keep the height difference between the tank and the carburetor within 1 cm, with the carburetor higher. Use 5 mm silicone fuel line and a fuel filter.
- Battery: a fully charged 11.1V 3S lithium battery.
- Timing belt: check that the marks on both pulleys line up. If the timing is off, no carburetor setting will fix it. See our Toyan V8 ignition timing guide.
Step-by-Step Tuning
Set the idle gap to 1.1 mm
Always set the idle gap first. With the throttle fully closed, adjust the idle stop so the throttle stays open by 1.1 mm.
How Jamie measures it: I use a paper clip, which is 1 mm, set loosely so the gap is about 1.1 mm. A drill bit shank works too.
Why first? The needles meter fuel for the air coming through the throttle. If the idle gap is wrong, every needle setting after it will be off too.
Set the low speed needle to 1.5 turns out
Gently turn the low speed needle clockwise until it just seats. Don't force it. Then open it 1.5 turns counterclockwise.
Stirlingkit Note: Toyan recommends never going below 1 turn on this needle. Running too lean at low speed can damage the engine.
Set the high speed needle
Gently seat the high speed needle, then open it. Jamie runs his with the needle flush with the carburetor body, approximately 3 turns out. The Toyan manual's reset value is 2.0 turns.
Jamie's high speed needle, set flush with the carburetor body.
| High speed needle | What Jamie saw |
|---|---|
| 2 turns (manual) | The engine cuts out. |
| 2.5 turns | Only a very small amount of oil comes out of the crankcase vent, and the engine heats up quickly. |
| 3 turns (Jamie) | Good lubrication, good throttle response and long running time. |
"In my 8-minute Toyan tuning run, the engine was running very strong at the end, and it could have kept running: the temperature stayed right around 80°C without overheating. A user can tune leaner from 3 turns for more power, but that is at your own discretion, because too lean can cause damage. This is a great running, safe setting that ensures engine longevity." — Jamie RCBlock
Stirlingkit Note: The crankcase vent is a simple health check: a little oily mist from it means the engine is getting enough oil. If you lean the needle from 3 turns for more power, go 15° at a time and watch the temperature.
Start the engine at about 30% throttle
Open the throttle to about 30% before starting. Press the start button for no more than 5 seconds at a time. If the engine doesn't start, let the starter cool for 15 seconds before trying again.
Stirlingkit Note: Don't open the throttle wide with no load. The engine can overheat quickly and damage the piston rings and cylinder sleeves.
Warm up for 30 seconds
Let the engine run slowly for at least 30 seconds so the oil in the fuel reaches every moving part. Always fine-tune with a warm engine; a cold engine gives misleading results.
Fine-tune in small steps
Listen to the exhaust and watch how the engine responds to the throttle, then adjust using the table below. Make one small change at a time and let the engine settle before judging the result.
Rich or Lean? How to Read Your Engine
| What you see or hear | Cause | Fix |
|---|---|---|
| Smoky exhaust, slow acceleration | Too rich | Turn the high speed needle clockwise, 15° at a time |
| Sharp, harsh sound like dry metal friction; temperature rises quickly; stalls right after accelerating | Too lean | Turn the high speed needle counterclockwise, 15° at a time |
| Dies when you drop from high to low speed | Idle mixture or idle gap | Check the idle gap first, then adjust the low speed needle 20° at a time until the idle is steady |
The goal: a soft but strong exhaust note, with just a little smoke and a light mist of oily fuel from the exhaust.
Warm Tips
FAQ
A proven starting point from Stirlingkit engine expert Jamie RCBlock: idle gap 1.1 mm, low speed needle 1.5 turns out, and high speed needle flush with the carburetor body (approx. 3 turns out). Fine-tune from there by sound and throttle response.
The idle gap. The needles meter fuel for the air passing through the throttle, so set the idle gap to 1.1 mm first, then the low speed needle, then the high speed needle.
Check that the idle gap is correct first. If it is, open or close the low speed needle in 20° steps until the engine holds a steady idle. Don't go below 1 turn out.
On Jamie's engine, 2 turns made the engine cut out, and 2.5 turns let only a little oil reach the crankcase vent while the engine heated up quickly. At 3 turns it keeps good lubrication, throttle response and running time, and holds around 80°C. Leaning it out for more power is possible, but at your own risk.
Use a paper clip. Most are about 1 mm thick, so set the gap so the paper clip fits slightly loose, and you're at about 1.1 mm. A drill bit shank works too.
Quality gasoline mixed with 2T engine oil at a ratio of 1:25 to 1:30.
Rich: smoky exhaust and slow acceleration. Lean: a sharp, harsh sound, quickly rising temperature, and stalling right after accelerating. Adjust the high speed needle 15° at a time to correct it.