MCU input
10–12V
Cison spec, never above 12V
Full 3S LiPo
~12.6V
Too high without a regulator
Jamie's setting
11V
3S LiPo + voltage regulator
11V → 12V
Small gain
Little extra RPM, more risk
New to MCU ignition? Key terms explained
- MCU: the small computer that controls the LS-52's ignition timing.
- 3S LiPo: a 3-cell lithium polymer battery. It is rated 11.1V, but reads about 12.6V when fully charged.
- Voltage regulator: a small module between the battery and the MCU that holds the output at a set voltage, such as 11V, no matter how full the battery is.
- CDI: capacitor discharge ignition, a traditional ignition box. The CISON Small-Block V8 (V8 Pro and Pro V1.1) uses a CDI ignition module. The LS-52 uses the MCU instead.
- Hall sensor: the sensor that detects crankshaft position and tells the ignition when to fire.
Recommended Power Setup for the LS-52 MCU
| Power source | Voltage | OK for the MCU? |
|---|---|---|
| 3S LiPo, fully charged, no regulator | ~12.6V | No — above the 12V limit |
| 3S LiPo + voltage regulator at 11V | 11V | Yes — Jamie's setup |
| 3S LiPo + voltage regulator at 12V | 12V | Yes — upper limit |
Why I Never Go Above 12 Volts
The reason I only go to a maximum of 12 volts with the MCU unit is that I have documentation saying the input voltage is 10–12 volts, and not to exceed this range. Cison says 12V max.
From what I saw in my LS-V8 coil test, going from 11V to 12V doesn't yield a dramatic difference in RPM. So there is very little to gain by pushing the voltage higher, and a lot to lose.
What I Learned from Burned-Out CDI Boxes
I used to use the maximum input voltage for the best spark, but I have seen 2 CDI boxes burn out for no reason. My theory is too much voltage. Since I started dropping the input voltage down to about 80% of the maximum, not one CDI box has burned out in 3 years.
The Hall Sensor Lesson
Then I found the problem with the Cison V8: the CDI box did not regulate the voltage going to the Hall sensor. The Hall sensor input is 3.3–12 volts, and a fully charged 3-cell LiPo is 12.6 volts. I believe this is why so many Hall sensors burned out right away on the Cison OHV engine. As soon as people started using less voltage, Hall sensors stopped burning out so much. I figured out that if you drop the input voltage down to 9 volts, the CDI unit doesn't burn out the Hall sensor so easily.
— Jamie RCBlock
Stirlingkit Note
The CDI and Hall sensor experience above comes from Jamie's years of running the CISON Small-Block V8 (V8 Pro), which uses a CDI ignition module rather than the MCU. The lesson carries over: keep input voltage within spec. For the LS-52 MCU, always follow Cison's specified 10–12V input range.
FAQ
What input voltage does the CISON LS-52 MCU need?
Cison's MCU documentation specifies 10–12V. Do not exceed 12V.
Can I connect a 3S LiPo directly to the MCU?
Not without a regulator. A fully charged 3S LiPo reads about 12.6V, which is above the 12V limit. Use a voltage regulator set to 10–12V. Jamie runs his at 11V.
Will higher voltage give my LS-52 more power?
Only a little. In Jamie's coil test, raising the input from 11V to 12V gave a small RPM gain and a slightly quicker throttle response. Going above 12V risks damaging the MCU.
Why do Hall sensors burn out?
In Jamie's experience with Cison engines, too much input voltage is a common cause. The Hall sensor input is 3.3–12V, so a fully charged 3S LiPo at 12.6V can exceed it. Keeping the input voltage within spec helps protect the sensor.
0 Kommentare