Toyan V8 FS-V800BGC carburetor high speed needle

How to Tune the Toyan V8 FS-V800BGC Carburetor: Idle Gap, Low & High Speed Needle Settings from Expert Jamie RCBlock | Stirlingkit

Toyan V8 FS-V800BGC carburetor high speed needle
J

A Stirlingkit guide based on the Toyan FS-V800WGPC / FS-V800BGC operating manual and the tested settings of Jamie RCBlock (YouTube: RCBlock), Stirlingkit engine expert. Reviewed, edited and published by the Stirlingkit team with Jamie's permission.

Idle gap

1.1 mm

Set this first

Low speed needle

1.5 turns

Never below 1 turn

High speed needle

2–3 turns

Manual 2.0 · Jamie 3

Fuel mix

25–30 : 1

Gasoline : 2T oil

A Toyan V8 that won't idle, bogs when you open the throttle, or dies when you snap it shut almost always comes down to three settings on the carburetor. This guide explains what each one does, gives you a proven starting point, and shows you how to fine-tune from there.

On Jamie's own FS-V800BGC, the factory carburetor setting needed retuning, so he started from zero and dialed it in step by step. These are the settings he ended up with.

New to carburetors? Key terms explained
  • Idle gap: how far the throttle stays open when the throttle is closed. It sets how much air the engine gets at idle.
  • Low speed needle (LSN): called the "auxiliary oil needle" in the Toyan manual. It controls the fuel mixture at idle and low RPM.
  • High speed needle (HSN): called the "main oil needle" in the Toyan manual. It controls the fuel mixture at mid to full throttle.
  • "Turns out": how many turns the needle is opened, counted from gently seated (fully closed). More turns = more fuel (richer).
  • Rich / lean: too much fuel / too little fuel for the amount of air.

Quick Settings: Toyan Manual vs Jamie

Setting Toyan manual Jamie RCBlock
Idle gap Less than 1.5 mm 1.1 mm — set this first
Low speed needle 1.5 turns (minimum 1 turn) 1.5 turns out
High speed needle 2.0 turns Flush with the carburetor body, approx. 3 turns out

Every engine is slightly different. Use these as a starting point, then fine-tune by sound and response as shown below.

Before You Start

  • Fuel: quality gasoline mixed with 2T engine oil at 1:25 to 1:30.
  • Fuel tank: about 100 cc, mounted level with the engine. Keep the height difference between the tank and the carburetor within 1 cm, with the carburetor higher. Use 5 mm silicone fuel line and a fuel filter.
  • Battery: a fully charged 11.1V 3S lithium battery.
  • Timing belt: check that the marks on both pulleys line up. If the timing is off, no carburetor setting will fix it. See our Toyan V8 ignition timing guide.

Step-by-Step Tuning

1

Set the idle gap to 1.1 mm

Always set the idle gap first. With the throttle fully closed, adjust the idle stop so the throttle stays open by 1.1 mm.

How Jamie measures it: I use a paper clip, which is 1 mm, set loosely so the gap is about 1.1 mm. A drill bit shank works too.

Why first? The needles meter fuel for the air coming through the throttle. If the idle gap is wrong, every needle setting after it will be off too.

2

Set the low speed needle to 1.5 turns out

Gently turn the low speed needle clockwise until it just seats. Don't force it. Then open it 1.5 turns counterclockwise.

Stirlingkit Note: Toyan recommends never going below 1 turn on this needle. Running too lean at low speed can damage the engine.

3

Set the high speed needle

Gently seat the high speed needle, then open it. Jamie runs his with the needle flush with the carburetor body, approximately 3 turns out. The Toyan manual's reset value is 2.0 turns.

Toyan V8 FS-V800BGC high speed needle set flush with the carburetor body

Jamie's high speed needle, set flush with the carburetor body.

High speed needle What Jamie saw
2 turns (manual) The engine cuts out.
2.5 turns Only a very small amount of oil comes out of the crankcase vent, and the engine heats up quickly.
3 turns (Jamie) Good lubrication, good throttle response and long running time.

"In my 8-minute Toyan tuning run, the engine was running very strong at the end, and it could have kept running: the temperature stayed right around 80°C without overheating. A user can tune leaner from 3 turns for more power, but that is at your own discretion, because too lean can cause damage. This is a great running, safe setting that ensures engine longevity." — Jamie RCBlock

Stirlingkit Note: The crankcase vent is a simple health check: a little oily mist from it means the engine is getting enough oil. If you lean the needle from 3 turns for more power, go 15° at a time and watch the temperature.

4

Start the engine at about 30% throttle

Open the throttle to about 30% before starting. Press the start button for no more than 5 seconds at a time. If the engine doesn't start, let the starter cool for 15 seconds before trying again.

Stirlingkit Note: Don't open the throttle wide with no load. The engine can overheat quickly and damage the piston rings and cylinder sleeves.

5

Warm up for 30 seconds

Let the engine run slowly for at least 30 seconds so the oil in the fuel reaches every moving part. Always fine-tune with a warm engine; a cold engine gives misleading results.

6

Fine-tune in small steps

Listen to the exhaust and watch how the engine responds to the throttle, then adjust using the table below. Make one small change at a time and let the engine settle before judging the result.

Rich or Lean? How to Read Your Engine

What you see or hear Cause Fix
Smoky exhaust, slow acceleration Too rich Turn the high speed needle clockwise, 15° at a time
Sharp, harsh sound like dry metal friction; temperature rises quickly; stalls right after accelerating Too lean Turn the high speed needle counterclockwise, 15° at a time
Dies when you drop from high to low speed Idle mixture or idle gap Check the idle gap first, then adjust the low speed needle 20° at a time until the idle is steady

The goal: a soft but strong exhaust note, with just a little smoke and a light mist of oily fuel from the exhaust.

Warm Tips

Write it downOnce your engine runs well, note your idle gap and needle positions. If anything gets bumped, you can return to a known-good setting in minutes.
One change at a timeChange only one setting per test run. If you change two at once, you won't know which one made the difference.
Small steps win15° on the high speed needle and 20° on the low speed needle is plenty. Big jumps overshoot the sweet spot.
Tune warm, not coldAlways warm the engine up for at least 30 seconds before judging a setting.
Rich is safer than leanWhen in doubt, err slightly rich. A lean engine runs hot and wears fast.
Keep it cleanDirt in the carburetor or a clogged air filter changes the mixture. Clean the carburetor inlet and check the filter regularly.
Mind the fuel lineA kinked line, air bubbles or a tank mounted too low can look like a carburetor problem. Check the fuel supply before turning the needles.
Flooded? Don't crankIf the engine floods, remove the spark plugs, close the needles and crank briefly to clear the fuel before trying again.

FAQ

What are the best carburetor settings for the Toyan V8 FS-V800BGC?

A proven starting point from Stirlingkit engine expert Jamie RCBlock: idle gap 1.1 mm, low speed needle 1.5 turns out, and high speed needle flush with the carburetor body (approx. 3 turns out). Fine-tune from there by sound and throttle response.

Which should I adjust first: the idle gap or the needles?

The idle gap. The needles meter fuel for the air passing through the throttle, so set the idle gap to 1.1 mm first, then the low speed needle, then the high speed needle.

My Toyan V8 dies when I drop the throttle. What should I do?

Check that the idle gap is correct first. If it is, open or close the low speed needle in 20° steps until the engine holds a steady idle. Don't go below 1 turn out.

Why does Jamie open the high speed needle 3 turns instead of the manual's 2?

On Jamie's engine, 2 turns made the engine cut out, and 2.5 turns let only a little oil reach the crankcase vent while the engine heated up quickly. At 3 turns it keeps good lubrication, throttle response and running time, and holds around 80°C. Leaning it out for more power is possible, but at your own risk.

How do I measure a 1.1 mm idle gap without a feeler gauge?

Use a paper clip. Most are about 1 mm thick, so set the gap so the paper clip fits slightly loose, and you're at about 1.1 mm. A drill bit shank works too.

What fuel does the Toyan V8 FS-V800BGC use?

Quality gasoline mixed with 2T engine oil at a ratio of 1:25 to 1:30.

How do I know if my engine is running rich or lean?

Rich: smoky exhaust and slow acceleration. Lean: a sharp, harsh sound, quickly rising temperature, and stalling right after accelerating. Adjust the high speed needle 15° at a time to correct it.

J

About Jamie RCBlock · Stirlingkit Engine Expert

Based in Canada, Jamie is a veteran of the model engine hobby and a true engine geek, with endless patience for every build. He puts each engine through hours of real running and shares exactly what he finds — the wins, the fixes, and the numbers.

▶ Watch Jamie on YouTube · RCBlock

More Toyan V8 Guides

0 コメント

コメントを残す

Meet the Author

Danna is the editor-in-chief of our website blog and has been worked with stirlingkit for over five years.

Stirlingkit

TOYAN FS-V800WGPC 1/10 Mini V8 Engine Model Building kits Run on Gas 28cc

通常価格
$1,099.99 から
セールスプライス
$1,099.99 から
通常価格
単価
per 

Stirlingkit

SEMTO ENGINE ST-NF2 DIY Build a Nitro 4 Stroke 2 Cylinder Engine Kit That Runs- FS-L200AC

通常価格
$199.99 から
セールスプライス
$199.99 から
通常価格
単価
per