Stirlingkit User Guide

Buy all Accessories for nr200 engine here. click 1. Can you install it into the boat? yes. our team has install NR-200 into the speedboat ( 85cm long). 1. Hi do you have any nr200 inlet manifold and carburetor on sale yet if so how much thanks We are currently...

buy accessories of this v twin engine. click Important: Before starting, please check whether the CDI is normally powered on, turn on the switch, and then rotate the flywheel to observe whether there is a high-voltage spark at the top of the spark plug. If there is no high-voltage spark....

Regarding the experience of a new car, especially the experience of KIT, which has a high threshold for novices, it is difficult for us to cover everything and achieve perfection. But we will use a quick and convenient way to regularly share the experience of loading and modification for everyone....

Dear Customer,Most items in Stirlingkit.com have paper instruction manual. Only a few of them have online instruction. when you receive your parcel, please check if there is a USB flash drive there, where the instructions is inserted into the USB. If it's missing or not working, you can also find...

DM227を5/27に発注し6/13に受け取りました。迅速な対応ありがとうございました。 現在製作中ですが送って貰いたい部品があります。 １． Positioning pins (063x2)が入ってませんでした。無い部品の画像はありません。 ２．Start gear (036) の穴が小さくモーター軸に入りません。穴をヤスリで広げましたが偏芯してしまいました。 ３．PCB (026) が動作テスト中発煙、焼損しました。PCBを通さずモーターに直接電池を繋ぐとエンジンは正常に回転します。 上記3点をお送りください。 よろしくお願いいたします。 部品を送って頂きありがとうございました。 組上がりましたが動作が正常でないです。 動画3篇添付します。 １．前進、後退が逆（これだけなら配線を繋ぎ変えれば済みますが） ２．操舵ができない（ギヤの遊びが大きい） ３．方向指示器の点灯仕方が異常（操舵時及び直進時共に） 対処法を教えてください。 ご回答ありがとうございました。 動画は見られましたか？ 走行はします。 サーボモータ軸の回転がギヤに正確に伝わらないのです。 それと、方向指示器の点灯が異常です。前進時と後退時に右ランプが点滅します。左折時に右ランプが点滅します。右折時に右ランプが点滅して左ランプが点滅して右ランプが点滅します 。 解決：1.モーターには2つの線があり、正と負の、曲を曲げる必要があります！ Chromeを使って、次のビデオを使用してください 2.問題の2例があります。最初に、古典的な車をやらせる、あなたが解決しなかったならば、電子ボード写真を見てください。3.現在のコーポレートの携帯電話アプリシステムにバグがあるため、現在は変更がありませんので、ターン信号は明るく異常に点灯し、システムは修理します。DM616トラクターのコントロールインターフェースでクラシックカーを運転できます。

If the engine is difficult to ignite, it may be that the camshaft angle is too small, and the exhaust gas will ignite if it is delayed a little bit, and the exhaust gas will easily be injected back in advance. 1. All the wire must be connected in order...

Latest upgrade: click here this is the most common question asked by our customers.Q1: Is there oil lubrication to the overhead cams or still grease only?A1: The camshaft is circulated by an oil pump and is lubricated by oil.Q2: Conrod big ends are they bronze bushed?A2: yes. With copper sleeve.Q3:...

Who invented Watt steam engine? The first working steam engine had been patented in 1698 and by the time of Watt's birth, Newcomen engines were pumping water from mines all over the country. In around 1764, James Watt was given a model Newcomen engine to repair. What is the Watt...

Q1: We are having a problem starting our M90. There is no spark from the spark plug. We have tried it with 2 batteries still nothing. The switch is in the on position.  it has compression no spark. What do we need to do next? A1: 1. Please try again...

Wichtiger Hinweis: (Bitte lesen Sie ihn, bevor Sie mit dem Bau dieses Motors beginnen)Wo kann man Toyan FS-L400 alles Zubehör kaufen: https://www.stirlingkit.com/collections/toyan-fs-l400-engine-parts 1. Kolbenringe: Unser Team hat die Kolbenringe im Voraus im Block montiert, da dies für den Durchschnittsmenschen sehr schwierig ist. Bitte folgen Sie der Bauanleitung und Sie werden...

Q: I recently  bought a C.D.I conversion kit for my Toyan FS- S100A to convert it from methanol to gasoline but it came without any fitting instructions and after spending a great deal of time examining it I can't figure out how to fit the hall sensor bracket to the...

Stirlingkit team has invited some youtubers to test FS-L400. you can check the videos below to know more about this engine. some of them are from our customers review. if you have something new, please send your youtube video to me. so i can update it in this blog. so...

If you want to convert a methanol engine into a gasoline engine, all you need to do is to remove the original flywheel, and then install the flywheel with magnets.and you also need to buy and replace the CDI Hall sensor igniter kit, spark plugs, and gasoline fuel yourself. After you have made it, add gasoline fuel and start your engine to check if it works.

How To Install and Debuge Stirling Engine? https://www.stirlingkit.com/products/stirling-engine-model-kit-generator-heat-engine-diy-assembly-model-set?_pos=1&_sid=5d4919e6f&_ss=rthere are three key factors for Stirling engine model debugging, one is resistance, the other is air tightness, and the other is heating temperature. to avoid resistance, please follow 4 steps below step by step. Firstly, when installing the flywheel and the small pulley,...

  M16 Mini Engine & Lombard Linn Halftrack Truck - Project Part 1

Important Notice: (Please read it before you start to build this engine) Where to Buy Toyan FS-L400 all Accessories: https://www.stirlingkit.com/collections/toyan-fs-l400-engine-parts 1. Piston Rings: Our team has assembled the piston rings in the cylinder liner in advance because it's very difficult to do it for the average people. pls follow the...